Daily maintenance and care of metal circular sawing machine

　　The quality of the metal circular sawing machine directly affects its service life. The poor quality of the circular sawing machine will also affect the normal use in the later period, but only good quality and not paying attention to maintenance will greatly reduce the knowledge of the circular sawing machine. Service life. Regular care can maintain the normal working condition of the machine, prolong the service life of the metal circular sawing machine, and minimize the mechanical failure rate of the metal circular sawing machine.

　　Circular saw machine

　　1. Before we use metal circular sawing machine and solid bar metal circular sawing machine to work, we need to check and maintain it. Make sure that the machine is in state before using the metal circular saw.

　　1. Check the amount of lubricating oil, which is the amount of engine oil we will, strictly follow the lubrication chart to keep the oil (grease), and maintain the proper amount of oil, and the oil path is unblocked. No rust, no root oil, no "yellow robe" sliding surface, no scratches, check whether the color of the engine oil is discolored or deteriorated.

　　2. Look at the appearance, whether the parts are in good condition, and ensure the safety device to make it safe and reliable.

　　3. Look at the power supply, like the solid bar metal circular saw machine, check the power supply circuit, check the motor wiring and electrical devices for short circuits, which belong to the normal energized state.

　　4. After seeing the first three points, we can move the metal circular sawing machine motor to make the metal circular sawing machine run, but this can only be dry running, and it is not possible to directly work and work. When the idle running time reaches 10 minutes , Let’s check and adjust each part of the main drive to ensure normal operation, whether the belt is directly driven by the belt is tight and proper, the direction and spacing of the circular saw blade are installed correctly, and there is no looseness; check and adjust the hydraulic system to make the handle flexible. Actions such as “clamping”, “unloading”, “infeed”, “return”, and “releasing” are accurate, the hydraulic oil is not lower than the scale line, the pump works reliably, and the hydraulic pipeline has no leakage; check and adjust the cooling system , So that the coolant is sufficient, no impurities, no deterioration, no leakage.

　　2. During the use of the metal circular sawing machine, there are some areas that need to be maintained, which need to be paid attention to.

　　1. For example, if we find that the metal circular sawing machine is running abnormally, we must stop it in time, conduct inspections, and check whether the main drive components, lubrication, hydraulics, cooling systems, and vices are working properly. The hydraulic and cooling systems have No noise or leakage, according to the tool box, the oil shall not be lower than 1/3 of the height of the marking line on the oil mark.

　　2. Always pay attention to the operation, temperature rise, sound, vibration, etc. of the motor and electrical appliances, and the rotation speed of the operation must be consistent, not too fast, so as to avoid the load of the metal circular saw.

　　3. In the working state of the metal circular sawing machine, the guide rail and the column are often strained, so once we find the guide rail and the column are strained, we must stop working, grind and maintain it in time.

　　4. In the working state of the metal circular sawing machine, the belt will turn over. If the belt is found to be turned over or damaged, it should be repaired or replaced in time.

　　5. Check or replace the incoming power fuse.

　　3. When the work of the metal circular saw is completed, maintenance is also required.

　　1. After the work of the metal circular saw machine is completed, the operating handles must be placed in neutral first, reset, and the switch positions of each part are also set to the neutral position, and all the operating devices are in the neutral state of non-operation, and the Turn on the power switch.

　　2. Clean the work site and maintain a clean environment at the work site. Wipe the exterior parts and parts of the metal circular saw to prevent dust and slag from entering the inside of the metal circular saw.

　　Develop a good use habit, like machinery, and metal circular sawing machine. As long as we use the metal circular sawing machine correctly in accordance with the operating rules, plus the maintenance of the metal circular sawing machine in time, then the use time of your metal circular sawing machine Will be longer.

Read recommendations:

CH11 Series丨Electric Pipe Cutter

RH21-2500 Pneumatic Chipping Hammer

Cutting Blades

Alloy Saw Blades

How to Distinguish the Quality of the Hydraulic Hose of a Hydraulic Torque Wrench?