You are here: > Home > News > Industry News

Hydraulic band sawing machine failure Daquan?

source:Industry News release time:2021-03-31 Article author:Rosit Popular:Air band saw

  Hydraulic band sawing machine failure Daquan?

  Screaming when sawing by band saw

  Causes of failure: 1. The saw blade speed is too fast or the feed rate is too large. 2. The coolant is selected improperly or the ratio is incorrect. 3. The guide block is too tight. 4. There are hard spots in the material;

Heavy pneumatic chain saw (4.5KW)

  Maintenance methods: 1. Reduce the speed or feed rate. 2. Replace the coolant. 3. Adjust the gap between the guide blocks. 4. Rotate the workpiece to a certain angle and then cut again.

  Band saw saw material skew

  Causes of failure: 1. Improper selection of saw teeth 2. Improper adjustment of the guide arm and the work surface or jaws are not perpendicular to the table 3. The gap between the guide blocks is too large 4. The saw blade is not symmetrical 5. The saw band is not tensioned enough 6. The feed is too large ;

  Maintenance method: 1. Choose a suitable saw band 2-3, re-adjust the gap between the guide arm and the guide block 4. Replace a suitable saw band 5, increase the tension 6, reduce the feed rate.

  Band sawing machine saw the band boring car skid or interrupted cutting

  Reasons for failure: 1. The feed is too large 2. The saw band is not tensioned enough;

  Maintenance method: 1. Reduce the feed rate 2. Increase the tension.

  Running belt when cutting by band saw

  Cause of failure: wear of two saw wheels;

  Repair method: replace the driven wheel.

  Tooth when cutting by band saw

  Causes of failure: 1. The workpiece is not clamped. 2. The feed rate is too large. 3. The saw tooth is too large. 4. The feed is uneven. 5. The saw blade is not straight and beats severely.

  Maintenance method: 1. Re-clamping work 2. Reduce the feed rate 3. Use small serrations 4. Check the speed control valve lift cylinder 5. Re-welding the saw blade.

  Band sawing machine breaks

  Causes of failure: 1. The tension is too large 2. The weld is not firm 3. The work clamp is not tight 4. The saw blade is of poor quality 5. The feed is too large;

  Maintenance method: 1. Reduce the tension 2. Re-welding 3. Clamp the workpiece 4. Replace the saw blade 5. Reduce the feed rate.


Read recommendations:

DP61-090 Emulsion Two Hand Operation Drill

GA21-125 Pneumatic Wet Grinder

Filter assy.

Carbide Inserts Twist Bits assy.丨DB83 Series

Selection elements of high-pressure vortex air pump

Previous:Detailed analysis of how many types of air motors are there Next:How does the hydraulic wrench ensure the accuracy of the torque?

related articles

Using Chainsaws to Cut Snow?

2024-05-21

What to do if the pneumatic wrench is weak

2022-12-19

Hydraulic chain saw

2022-12-13

Operation of the wrench

2022-12-06

Introduction to the principle of pneumatic wrench

2022-11-28

How to use the pneumatic wrench

2022-11-21

Brief introduction to the principle of pneumatic wrench

2022-11-14

Impact pneumatic wrench

2022-11-07

Correct hydraulic wrench operation procedure

2022-11-01

Hydraulic wrench torque pressure conversion

2022-11-01

Field operation procedure of hydraulic wrench

2022-10-24

Hydraulic radial plunger motor

2022-10-17

The history of hydraulic motors

2022-10-17

Principle of balance hydraulic wrench

2022-10-10

The Price Factor of Smart Electric Torque Wrench

2022-10-10

Introduction to the advantages of using intelligent electric torque wrench

2022-10-10

The Price Factor of Smart Electric Torque Wrench

2022-10-10

Classification and use of wrenches

2022-10-10

hydraulic wrench pressure conversion

2022-10-10

Introduction to the advantages of the use of intelligent electric torque wrench

2022-10-10

Smart Electric Torque Wrench Selection Guide

2022-10-10

Intelligent electric torque wrench for wind power generation

2022-10-09

Uses of open-end wrenches.Pneumatic chainsaw

2022-10-08

What are the driving parts of a hydraulic wrench and what they do

2022-09-30

What are the driving parts of a hydraulic wrench and what they do

2022-09-23

the commonly used wrenches

2022-09-22

Introduction of several common wrenches

2022-09-21

Application scope and daily maintenance method of hydraulic bolt tensioner

2022-09-20

Characteristics of hollow hydraulic wrench and precautions for use

2022-09-19

Characteristics and precautions of driving hydraulic wrench

2022-09-17

Power Tools

CD31-630 Hydraulic Concrete Chainsaw

2023-06-16

CC21-380 Pneumatic Chainsaw (3.0 kw Series)

2022-12-08

DC21-300 Pneumatic Core Drill

2023-01-03

CH31 series Hydraulic Pipe Cutter

2022-12-12

CR21-002 Light Pneumatic Reciprocating Saw

2021-06-07

OW62-020 Integrated Emulsion Mining Waterjet Cutting Machine

2023-05-10

AW22-4000 Pneumatic Impact Wrench (Ultra-Light Series)

2021-06-15

DP22-150 Pneumatic Column Drill

2020-06-13

AN32-23000 Hollow Hydraulic Wrench

2023-06-27

CN22-110130 Nut Cutter丨Split-type Nut Cutter

2023-06-17

LH22-016 Pneumatic Hoist

2023-06-29

LH61-015 Emulsion Hoist

2023-06-29

DC21-100 Pneumatic Core Drill

2023-06-20

DM22-023 Pneumatic Rail Drill

2023-06-19

OW65-020 Split Emulsion Type Mining Waterjet Cutting Machine

2023-05-10

AN51-3000 Electric servo CNC Torque Wrench

2023-06-27

GP61-200 Emulsion Submersible Pump

2023-06-29

DL21-013 Pneumatic Pistol Hammer Drill

2021-06-10

GG11-100 Electric Angle Grinder

2023-06-28

RZ21-014 Pneumatic Rammer

2022-12-28

OW61-020 Integrated Emulsion Mining Waterjet Cutting Machine

2023-05-10

CB11-120 Electric Band Saw

2020-06-13

OF27-100 Heavy Fixed Fan

2022-12-29

OF27-270 Heavy Fixed Fan

2023-06-28

AK21-030 Pneumatic C-Hog Ring Plier (1.5 coil)

2022-12-12

CB22-160 Pneumatic Band Saw - Stainless Steel Series

2023-06-16

AN23-2500 Pneumatic Torque Wrench (Angle Shaft)

2024-03-12

OF22-500 Pneumatic Fan (light/medium)

2022-12-29

AN22-4500 Pneumatic Torque Wrench (straight shaft)

2023-06-27

DB21-022 Pneumatic Rotary Drill Heavy Duty

2023-06-19