You are here: > Home > News > Industry News

How to better use high-speed steel circular saw blades

source:Industry News release time:2021-06-03 Article author:Rosit Popular:Air band saw

  In order to minimize the consumption of high-speed steel circular saw blades, reduce the cutting cost per blade, and improve the production efficiency of the factory, according to the actual situation, based on our years of industry service experience, the following application suggestions are listed here:

How to better use high-speed steel circular saw blades(pic1)

  1. Trial operation of the new saw blade.

  In order to prolong the service life, make the metal circular saw and the new saw blade (new unused saw blade or saw blade after each grinding) have a more sufficient running-in process. The feed rate is very necessary.

  2. Cutting and feeding speed.

    Cutting speed depends on the cross section and toughness of the workpiece to be cut. For stainless steel, which is difficult to cut and has higher toughness, a slower speed is very helpful to increase the service life of the saw blade. For some iron-based materials with relatively low toughness, the speed of the saw blade can be increased accordingly.

  3. Grind the saw blade in time and correctly.

    Pay attention to the working condition of the saw blade at any time. If there are abnormalities such as vibration, noise, and material removal on the processing surface, it must be stopped in time for adjustment, and timely grind to maintain sharpness. Re-grind the saw blade in time and correctly can maximize the effectiveness of the saw blade.

  4. Add suitable coolant.

    Because of the high temperature generated during cutting, the saw blade may be deformed. There is no coolant, which not only affects the life of the saw blade, but also the cutting effect is not ideal. So, please add coolant.

  5. Observing the sawdust allows you to roughly judge the current performance status of the saw blade.

    1) The sawdust is very fine or powdery, which means that the cutting pressure is too small.

    2) Thick and soft sawdust, which means cutting overload.

    3) The sawdust is a long spiral filament, which means it is in good condition.

    4) If the feed speed is increased, a thicker tooth should be selected accordingly.


Read recommendations:

LH11-010 Electric Hoist

CS31-180 Hydraulic Handheld Circular Saw

Ex-proof Sleeves

Filter assy.

Multifunctional saw blade tells the story of band saw blade

Previous:The main steps of the installation and test machine of the sawing machine Next:The main steps of the installation and test machine of the sawing machine

related articles

Using Chainsaws to Cut Snow?

2024-05-21

What to do if the pneumatic wrench is weak

2022-12-19

Hydraulic chain saw

2022-12-13

Operation of the wrench

2022-12-06

Introduction to the principle of pneumatic wrench

2022-11-28

How to use the pneumatic wrench

2022-11-21

Brief introduction to the principle of pneumatic wrench

2022-11-14

Impact pneumatic wrench

2022-11-07

Correct hydraulic wrench operation procedure

2022-11-01

Hydraulic wrench torque pressure conversion

2022-11-01

Field operation procedure of hydraulic wrench

2022-10-24

Hydraulic radial plunger motor

2022-10-17

The history of hydraulic motors

2022-10-17

Principle of balance hydraulic wrench

2022-10-10

The Price Factor of Smart Electric Torque Wrench

2022-10-10

Introduction to the advantages of using intelligent electric torque wrench

2022-10-10

The Price Factor of Smart Electric Torque Wrench

2022-10-10

Classification and use of wrenches

2022-10-10

hydraulic wrench pressure conversion

2022-10-10

Introduction to the advantages of the use of intelligent electric torque wrench

2022-10-10

Smart Electric Torque Wrench Selection Guide

2022-10-10

Intelligent electric torque wrench for wind power generation

2022-10-09

Uses of open-end wrenches.Pneumatic chainsaw

2022-10-08

What are the driving parts of a hydraulic wrench and what they do

2022-09-30

What are the driving parts of a hydraulic wrench and what they do

2022-09-23

the commonly used wrenches

2022-09-22

Introduction of several common wrenches

2022-09-21

Application scope and daily maintenance method of hydraulic bolt tensioner

2022-09-20

Characteristics of hollow hydraulic wrench and precautions for use

2022-09-19

Characteristics and precautions of driving hydraulic wrench

2022-09-17

Power Tools

AN11-6000 Electric servo CNC Torque Wrench

2023-06-27

CW21-022 Pneumatic Bender

2022-12-12

DM11-050 Electric Magnetic Drill

2023-06-19

OW63-020 Integrated Emulsion Mining Waterjet Cutting Machine

2023-05-10

DB21-032 Pneumatic Rotary Drill Heavy Duty

2020-11-24

CD22-500 Pneumatic Concrete Chainsaw (5.0KW)

2023-06-16

AW22-750 Pneumatic Impact Wrench (Ultra-Light Series)

2022-12-20

AN22-4500 Pneumatic Torque Wrench (straight shaft)

2023-06-27

CC23-430 Pneumatic Chainsaw Heavy-Duty (3.5KW Series)

2023-06-14

AN71-3500 Torque Multiplier

2023-06-29

DM22-016 Pneumatic Rail Drill

2020-06-13

CD22-380 Pneumatic Concrete Chainsaw (5.0KW)

2023-06-16

AN51-2000 Electric servo CNC Torque Wrench

2023-06-27

GP61-100 Emulsion Submersible Pump

2023-06-29

AN21-300 Pneumatic Nut Runner

2022-12-20

AN31-70000 Hydraulic Torque Wrench

2023-06-27

RZ21-020 Pneumatic Rammer

2023-06-27

CB22-260 Pneumatic Band Saw - Stainless Steel Series

2023-06-16

RZ21-014 Pneumatic Rammer

2022-12-28

DP21-140 Pneumatic Two Hand Operation Drill

2021-06-15

GG21-178 Pneumatic Angel Grinder

2020-06-13

GG21-125 Pneumatic Angel Grinder

2021-06-15

CB11-210 Electric Band Saw

2023-05-18

DH21-050 Pneumatic Hammer Drill

2021-06-10

AW22-2000 Pneumatic Impact Wrench (Ultra-Light Series)

2021-06-15

CH31 series Hydraulic Pipe Cutter

2022-12-12

AN31-20000 Hydraulic Torque Wrench

2023-06-27

DP21-080 Pneumatic Two Hand Operation Drill

2021-06-15

AK21-110 Pneumatic C-Hog Ring Plier (1.5 coil)

2023-06-29

CR21-003 Light Pneumatic Reciprocating Saw

2021-06-07