You are here: > Home > News > Industry News

Correctly install hydraulic wrench high pressure hose fittings

source:Industry News release time:2022-03-30 Article author:Rosit Popular:Air band saw

  AN22-750/1800/2500/3500 Pneumatic Torque Wrenches

  1. The high-pressure hose of the hydraulic wrench cannot be bent excessively or at the root when it is moving or stationary, and it must be bent at least 1.5 times its diameter;

  2. When the high-pressure hose of the hydraulic wrench moves to the extreme position, it should not be pulled too tight, and should be relatively loose;

  3. Try to avoid torsional deformation of the hose;

  4. The high-pressure hose of the hydraulic wrench should be kept away from the heat radiation components as far as possible, and a heat shield should be installed if necessary;

  5. External damage to the hose should be avoided, such as long-term friction on the surface of the same component during use;

  6. If the hose is excessively deformed by its own weight, there should be a supporting piece.

  The maintenance of the hydraulic wrench drive shaft in normal use can better ensure the use of the hydraulic wrench and effectively reduce the occurrence of failures. The hydraulic wrench drive shaft is an indispensable inspection and regular maintenance item for the normal maintenance of the hydraulic wrench. Because of all rubber products, sealing rings, etc. in the hydraulic wrench, the validity period is usually three years. The hydraulic wrench will experience natural aging and cracking after repeated stretching and squeezing during long-term work. Of course, it also includes damage caused by abnormal conditions.

  Over time, the grease in it may have deteriorated, and it needs to be cleaned and replaced with new grease. It is absolutely possible to consider regular maintenance to prevent problems before they occur.

  1. The hydraulic wrench drive shaft should be pulled out regularly to clean the dirt on it. If it is not used for a long time, apply a layer of anti-rust oil to prevent it from corroding and rusting.

  2. The gears on the drive shaft of the hydraulic wrench should also be frequently cleaned of the ash layer and scum in the gear gap.

  3. When disassembling the hydraulic wrench drive shaft, first loosen the lock cap, and then pull out the hydraulic wrench drive shaft to prevent destructive and brutal disassembly.


Read recommendations:

GG11-125 Electric Angle Grinder

CF21-005 Pneumatic Cutter

Hard Alloy Hollow Drill Bits assy.丨DB84 Series

Filter assy.

Selection of the Torque Wrench

Previous:Selection of hydraulic wrench and its application in construction machinery Next:Hydraulic wrench companies in the hardware industry also need a sense of crisis.Hollow hydraulic wre

related articles

Using Chainsaws to Cut Snow?

2024-05-21

What to do if the pneumatic wrench is weak

2022-12-19

Hydraulic chain saw

2022-12-13

Operation of the wrench

2022-12-06

Introduction to the principle of pneumatic wrench

2022-11-28

How to use the pneumatic wrench

2022-11-21

Brief introduction to the principle of pneumatic wrench

2022-11-14

Impact pneumatic wrench

2022-11-07

Correct hydraulic wrench operation procedure

2022-11-01

Hydraulic wrench torque pressure conversion

2022-11-01

Field operation procedure of hydraulic wrench

2022-10-24

Hydraulic radial plunger motor

2022-10-17

The history of hydraulic motors

2022-10-17

Principle of balance hydraulic wrench

2022-10-10

The Price Factor of Smart Electric Torque Wrench

2022-10-10

Introduction to the advantages of using intelligent electric torque wrench

2022-10-10

The Price Factor of Smart Electric Torque Wrench

2022-10-10

Classification and use of wrenches

2022-10-10

hydraulic wrench pressure conversion

2022-10-10

Introduction to the advantages of the use of intelligent electric torque wrench

2022-10-10

Smart Electric Torque Wrench Selection Guide

2022-10-10

Intelligent electric torque wrench for wind power generation

2022-10-09

Uses of open-end wrenches.Pneumatic chainsaw

2022-10-08

What are the driving parts of a hydraulic wrench and what they do

2022-09-30

What are the driving parts of a hydraulic wrench and what they do

2022-09-23

the commonly used wrenches

2022-09-22

Introduction of several common wrenches

2022-09-21

Application scope and daily maintenance method of hydraulic bolt tensioner

2022-09-20

Characteristics of hollow hydraulic wrench and precautions for use

2022-09-19

Characteristics and precautions of driving hydraulic wrench

2022-09-17

Power Tools

AN31-180000 Hydraulic Torque Wrench

2023-06-27

AK21-080 Pneumatic C-Hog Ring Plier (1.5 coil)

2023-06-29

DA21-015 Pneumatic Angle Drill

2022-12-15

AW22-3000 Pneumatic Impact Wrench (Ultra-Light Series)

2021-06-15

AK21-065 Pneumatic C-Hog Ring Plier (1.5 coil)

2023-06-29

DA21-100 Pneumatic Angle Drill

2023-06-19

OF25-260 Pneumatic Fan (light/medium)

2023-06-28

OF25-190 Pneumatic Fan (light/medium)

2022-12-29

OW65-020 Split Emulsion Type Mining Waterjet Cutting Machine

2023-05-10

CC20-430 Pneumatic Chainsaw (3.0 kw Series)

2023-06-02

RH31-1000 Hydraulic Chipping Hammer

2023-06-27

AK51-030 Pneumatic C-Hog Ring Plier (Charging/Manual 1.5 coil)

2022-12-12

CS31-120 Hydraulic Handheld Circular Saw

2022-12-09

CS21-085 Pneumatic Handheld Circular Saw

2021-06-08

AN23-8000 Pneumatic Torque Wrench (Angle Shaft)

2024-03-12

LH22-010 Pneumatic Hoist

2023-06-29

OF27-100 Heavy Fixed Fan

2022-12-29

AW21-2700 Pneumatic Impact Wrench (Ex-proof Series)

2022-12-19

DH21-040 Pneumatic Hammer Drill

2022-12-13

LH12 Series Chain Hoist

2023-05-11

AN11-3000 Electric servo CNC Torque Wrench

2023-06-27

LH11-005 Electric Hoist

2023-05-11

LW21-020 Pneumatic Winch

2023-06-29

OF24-060 Pneumatic Fan (light/medium)

2022-12-29

AW22-750 Pneumatic Impact Wrench (Ultra-Light Series)

2022-12-20

CF21-005 Pneumatic Cutter

2022-12-12

LH61-032 Emulsion Hoist

2023-06-29

DP22-150 Pneumatic Column Drill

2020-06-13

AK21-130 Pneumatic C-Hog Ring Plier (1.5 coil)

2023-06-29

CC21-380 Pneumatic Chainsaw (3.0 kw Series)

2022-12-08