Language

English Espana Deutschland Chinese

Visitor Center

My Wish List Last Viewed Products

English Espana Deutschland Chinese

My wish list Last viewed products

You are here: > Home > News > Industry News

News

What should be paid attention to in hydraulic wrench hydraulic oil

source:Industry News release time:2021-10-27 Article author:Rosit Popular:Air band saw

　　What should be paid attention to in hydraulic wrench hydraulic oil

　　1. Keep the hydraulic oil clean and prevent impurities such as metal chips and fibers from entering the oil.

　　2. The oil tank should be thoroughly cleaned before adding oil, and the new oil must be filtered (the accuracy of the filter is generally 5-10μm), otherwise the performance of the hydraulic system and the life of the hydraulic pump will be greatly affected .

What should be paid attention to in hydraulic wrench hydraulic oil(pic1)

　　3. Regularly check the oil quality and oil level.

　　4. It should be ensured that the temperature rise of the oil in the oil tank does not exceed the allowable range of the hydraulic oil, and all work generally requires not to exceed 60°C, otherwise the cooling system of the hydraulic oil needs to be checked. When the oil temperature is too low, the oil should be preheated so that the oil temperature gradually rises (requires a temperature of more than 30°C) before running the machine.

　　5. The best temperature of the hydraulic system oil temperature is between 35～55℃. Once the temperature rises above 60℃, the performance of the hydraulic system will be greatly reduced, hydraulic equipment failures will continue to appear, the ideal working oil temperature of the hydraulic system It is between 45 and 50 degrees. The reason is that the hydraulic system is designed according to a selected pressure oil viscosity, but the viscosity will change with the oil temperature, which will affect the working components in the system, such as cylinders and hydraulic valves. Reduce the control accuracy and response sensitivity. At the same time, too high a temperature will accelerate the aging of the seal, causing it to harden and crack. Therefore, it is necessary to pay close attention to the working temperature of hydraulic oil.

　　6. According to the hydraulic pump outlet pressure and oil temperature, select varieties:

　　HL for pressure lower than 7.0MPa:

　　For pressure from 7.0 to 14.0MPa, HL or HM is used for oil temperature below 50 degrees Celsius, and HM is used for oil temperature above 50 degrees Celsius to 80.

　　The pressure is greater than 14.0MPa, and the oil temperature is 50 to 80 degrees Celsius with HM.

　　The new hydraulic pump uses No. 32 and No. 46 hydraulic oil, and the old pump uses No. 46 and No. 68 and above. If the pressure is greater than 30.0MPa, the higher level 1-2 should be selected accordingly.

Read recommendations:

DB21-070 Pneumatic Rotary Drill Heavy Duty

DA21-100 Pneumatic Angle Drill

Carbide Inserts Twist Bits丨DB82 Series

Calculation of duct resistance of vortex fan

Previous:Tips for extending the life of hydraulic wrenches Next:How to choose a hydraulic wrench?Air band saw Vendor

related articles

Using Chainsaws to Cut Snow?

What to do if the pneumatic wrench is weak

Hydraulic chain saw

Operation of the wrench

Introduction to the principle of pneumatic wrench

How to use the pneumatic wrench

Brief introduction to the principle of pneumatic wrench

Impact pneumatic wrench

Correct hydraulic wrench operation procedure

Hydraulic wrench torque pressure conversion

Field operation procedure of hydraulic wrench

Hydraulic radial plunger motor

The history of hydraulic motors

Principle of balance hydraulic wrench

The Price Factor of Smart Electric Torque Wrench

Introduction to the advantages of using intelligent electric torque wrench

The Price Factor of Smart Electric Torque Wrench

Classification and use of wrenches

hydraulic wrench pressure conversion

Introduction to the advantages of the use of intelligent electric torque wrench

Smart Electric Torque Wrench Selection Guide

Intelligent electric torque wrench for wind power generation

Uses of open-end wrenches.Pneumatic chainsaw

What are the driving parts of a hydraulic wrench and what they do

What are the driving parts of a hydraulic wrench and what they do

the commonly used wrenches

Introduction of several common wrenches

Application scope and daily maintenance method of hydraulic bolt tensioner

Characteristics of hollow hydraulic wrench and precautions for use

Characteristics and precautions of driving hydraulic wrench

Power Tools

RC21-1500 Pneumatic Long Reach Scalers

DP61-160 Emulsion Two Hand Operation Drill

CD31-250 Hydraulic Concrete Chainsaw

CH11 Series丨Electric Pipe Cutter

AN71-15000 Torque Multiplier

GG11-178 Electric Angle Grinder

DL21-008 Pneumatic Pistol Hammer Drill

LH61-010 Emulsion Hoist

GP61-200 Emulsion Submersible Pump

CN22-70115 Nut Cutter丨Split-type Nut Cutter

DC21-150 Pneumatic Core Drill

AK22-130 Pneumatic C-Hog Ring Plier (2.0 coil)

LH22-020 Pneumatic Hoist

DA21-100 Pneumatic Angle Drill

DB21-022 Pneumatic Rotary Drill Heavy Duty

DP21-080 Pneumatic Two Hand Operation Drill

AK71-130 Manual C-Hog Ring Plier (1.5 coil)

LH21 Series Pneumatic Hoist

RH21-150 Pneumatic Chipping Hammer

DM31-035 Hydraulic Magnetic Drill

AN31-20000 Hydraulic Torque Wrench

AN11-3000 Electric servo CNC Torque Wrench

RH21-4500 Pneumatic Chipping Hammer

OF25-260 Pneumatic Fan (light/medium)

CS31-160 Hydraulic Handheld Circular Saw

AN22-1800 Pneumatic Torque Wrench (Straight Shaft)

CB61-120丨Emulsion Band Saw

GG21-230 Pneumatic Angel Grinder

OF23-880 Pneumatic Fan/ (light/medium)

AN51-600 Charging CNC Torque Wrench

Accessories

Alloy Saw Blades丨CR812 Series

Abrasive Blades

Regular Saw Chains丨CC811 Series

Alloy Saw Blades丨CR811 Series

Grinding Disc

Water Pump

Carbide Hollow Rail Drill Bits丨DM822 Series

Hard Alloy Hollow Drill Bits assy.丨DB84 Series

Alloy Saw Blades丨CR814 Series

Sleeve KIT

Integrated Hollow Drill Bits丨DC81

Alloy Drill Bits丨813 Series

Tool Bits

Alloy Drill Bits丨812 Series

Pipe Fixed Clamps丨CB861-18

Diamond Saw Chains丨CC813 Series

Cutting Blades

Chisels

Alloy Saw Blades

Carbide Hollow Bits丨DM816 Series

Alloy Twist Drill Bits丨DB81 Series

Platform Clamps丨CB863-19

Alloy Guide Bars丨CC814 Series

Diamond Saw Blades

Split Hollow Drill Bits丨DC82

Alloy Saw Chains丨CC812/CC816 Series

Core Drill Morse Taper Sleeves

Hydraulic Pump Station

Clamps

Alloy Saw Blades

CONTACT: +49 69 6780 8096; +49 69 6780 8326; info@rosit.eu

COMPANY INFO

ABOUT NEWS
PRODUCT SUPPORT

WARRANTY TOOL MAINTENANCE FAQs
CUSTOMER SERVICE

SERVICE CENTER CONTACT US Enquiry
CONTACT

+49 69 6780 8096 +49 69 6780 8326 info@rosit.eu
Follow Us