Language

English Espana Deutschland Chinese

Visitor Center

My Wish List Last Viewed Products

English Espana Deutschland Chinese

My wish list Last viewed products

You are here: > Home > News > Industry News

News

What are the reasons for the high temperature of the vortex air pump

source:Industry News release time:2021-08-28 Article author:Rosit Popular:Air band saw

　　What are the reasons for the excessively high temperature of the vortex air pump? While the vortex air pump brings simple and efficient production to factories or enterprises, it is inevitable that various problems will arise. From the design point of view, the vortex fan is compared with other machinery. It is almost equivalent to the name maintenance, it can run for a long time without special overhaul, but all equipment is not omnipotent, and more or less problems will occur after long use, and the frequent problem is the temperature of the high-pressure fan Too high. What caused it, and how to deal with it?

　　Too high temperature will cause the bearing and impeller to become unstable, which will affect or damage the high-pressure vortex fan. Therefore, the temperature is too high. It is not as good as underestimated. The Nasid high-pressure fan adopts high-temperature-resistant customized bearings, which can withstand a high temperature of 160 degrees, causing high-pressure fans. The reasons for temperature over can refer to the following points:

　　First, the reason for the rolling bearing configuration, everyone must pay attention to this is to try not to appear too large or small when configuring these bearings, even if it is just a little bit, it may affect the whole body.

　　Second, the problem of the sealing felt, this is a detail, that is, just be careful not to be too tight or too loose.

　　Third, check whether the purchased fan is suitable for the actual operating conditions. If the selected model is small, the long-term overload operation temperature will increase.

　　The operating temperature of the high-pressure fan must be controlled within an appropriate range. If the temperature is too high, there will be no problems in the inspection. You can contact the manufacturer or after-sales service.

Read recommendations:

AW22-8000 Pneumatic Impact Wrench (Ultra-Light Series)

GG21-125 Pneumatic Angel Grinder

Pipe Fixed Clamps丨CB861-12

Alloy Saw Blades丨CR812 Series

How to Operate the Pneumatic Winch?

Previous:What are the advantages of air pumps over ordinary air pumps Next:Small equipment and big power, high-pressure vortex air pump

related articles

Using Chainsaws to Cut Snow?

What to do if the pneumatic wrench is weak

Hydraulic chain saw

Operation of the wrench

Introduction to the principle of pneumatic wrench

How to use the pneumatic wrench

Brief introduction to the principle of pneumatic wrench

Impact pneumatic wrench

Correct hydraulic wrench operation procedure

Hydraulic wrench torque pressure conversion

Field operation procedure of hydraulic wrench

Hydraulic radial plunger motor

The history of hydraulic motors

Principle of balance hydraulic wrench

The Price Factor of Smart Electric Torque Wrench

Introduction to the advantages of using intelligent electric torque wrench

The Price Factor of Smart Electric Torque Wrench

Classification and use of wrenches

hydraulic wrench pressure conversion

Introduction to the advantages of the use of intelligent electric torque wrench

Smart Electric Torque Wrench Selection Guide

Intelligent electric torque wrench for wind power generation

Uses of open-end wrenches.Pneumatic chainsaw

What are the driving parts of a hydraulic wrench and what they do

What are the driving parts of a hydraulic wrench and what they do

the commonly used wrenches

Introduction of several common wrenches

Application scope and daily maintenance method of hydraulic bolt tensioner

Characteristics of hollow hydraulic wrench and precautions for use

Characteristics and precautions of driving hydraulic wrench

Power Tools

CW21-022 Pneumatic Bender

AN31-100000 Hydraulic Torque Wrench

DB21-032 Pneumatic Rotary Drill Heavy Duty

AW41-1500 Emulsion Impact Wrench

CR21-003 Light Pneumatic Reciprocating Saw

LH11-005 Electric Hoist

DM11-050 Electric Magnetic Drill

DH21-026 Pneumatic Hammer Drill

CB11-200 Electric Band Saw

GG21-100 Pneumatic Angle Grinder

CR21-002 Light Pneumatic Reciprocating Saw

CD31-630 Hydraulic Concrete Chainsaw

AN22-1800 Pneumatic Torque Wrench (Straight Shaft)

CD31-380 Hydraulic Concrete Chainsaw

CC23-530 Pneumatic Chainsaw Heavy-Duty (3.5KW Series)

GA21-100 Pneumatic Wet Grinder

AN31-48000 Hydraulic Torque Wrench

CC21-630 Pneumatic Chainsaw (3.0 kw Series)

AN32-5000 Hollow Hydraulic Wrench

DM31-013 Hydraulic Magnetic Drill

DP61-110 Emulsion Two Hand Operation Drill

AN23-4500 Pneumatic Torque Wrench (Angle Shaft)

RH21-2300 Pneumatic Chipping Hammer

RH31-2100 Hydraulic Chipping Hammer

LW21-003 Pneumatic Winch

DP61-160 Emulsion Two Hand Operation Drill

RC21-350 Pneumatic Long Reach Scalers

OF24-060 Pneumatic Fan (light/medium)

GP61-200 Emulsion Submersible Pump

AK22-110 Pneumatic C-Hog Ring Plier (2.0 coil)

Accessories

Filter assy.

Split Hollow Drill Bits丨DC82

Carbide Hollow Bits丨DM818 Series

Diamond Saw Chains

Oiler

Alloy Sleeves

Alloy Drill Bits丨812 Series

Tool Bits

Chisels

Diamond Saw Blades

Hydraulic Regulating Valve

Abrasive Blades

Alloy Drill Bits丨811 Series

Guide Bars

Water Pump

Alloy Saw Blades丨CR811-150/152

Carbide Inserts Twist Bits assy.丨DB83 Series

Non-metallic Alloy Saw Blades

Diamond Saw Blades

Platform Clamps丨CB863-19

Alloy Twist Drill Bits

Rail Clamps丨CB864-12

Alloy Guide Bars丨CC814 Series

Carborundum Saw Chains

Ex-proof Sleeves

Alloy Twist Drill Bits丨DB81 Series

Alloy Saw Blades丨CR812 Series

Pipe Fixed Clamps丨CB861-18

Clamps

Optional Accessories

CONTACT: +49 69 6780 8096; +49 69 6780 8326; info@rosit.eu

COMPANY INFO

ABOUT NEWS
PRODUCT SUPPORT

WARRANTY TOOL MAINTENANCE FAQs
CUSTOMER SERVICE

SERVICE CENTER CONTACT US Enquiry
CONTACT

+49 69 6780 8096 +49 69 6780 8326 info@rosit.eu
Follow Us